|
# Akadia AG, Arvenweg 4, CH-3604
Thun
workers.properties
# --------------------------------------------------------------------------
# File: workers.properties
#
# Autor: Martin Zahn, 06.08.2002
#
# Purpose: Configuration file for Apache/Tomcat
#
# Location: $TOMCAT_HOME/conf
#
# Certified: RedHat Linux 7.2 / Apache 1.3.22 / Tomcat 4.1.10 / JDK-1.4
#
# Note: This file should be appended or included into
your mod_jk.conf
# --------------------------------------------------------------------------
#
# This file provides jk derived plugins with the needed information to
# connect to the different tomcat workers. Note that the distributed
# version of this file requires modification before it is usable by a
# plugin.
#
# As a general note, the characters $( and ) are used internally to define
# macros. Do not use them in your own configuration!!!
#
# Whenever you see a set of lines such as:
# x=value
# y=$(x)\something
#
# the final value for y will be value\something
#
# Normaly all you will need to do is un-comment and modify the first three
# properties, i.e. workers.tomcat_home, workers.java_home and ps.
# Most of the configuration is derived from these.
#
# When you are done updating workers.tomcat_home, workers.java_home and ps
# you should have 3 workers configured:
#
# - An ajp12 worker that connects to localhost:8007
# - An ajp13 worker that connects to localhost:8009
# - A jni inprocess worker.
# - A load balancer worker
#
# However by default the plugins will only use the ajp12 worker. To have
# the plugins use other workers you should modify the worker.list property.
#
# OPTIONS ( very important for jni mode )
#
# workers.tomcat_home should point to the location where you
# installed tomcat. This is where you have your conf, webapps and lib
# directories.
#
workers.tomcat_home=/usr/local/tomcat
#
# workers.java_home should point to your Java installation. Normally
# you should have a bin and lib directories beneath it.
#
workers.java_home=/usr/local/java
#
# You should configure your environment slash... ps=\ on NT and / on UNIX
# and maybe something different elsewhere.
#
ps=/
#
#------ ADVANCED MODE ------------------------------------------------
#---------------------------------------------------------------------
#
#------ DEFAULT worket list ------------------------------------------
#---------------------------------------------------------------------
#
# The workers that your plugins should create and work with
#
worker.list=ajp12, ajp13
#
#------ DEFAULT ajp12 WORKER DEFINITION ------------------------------
#---------------------------------------------------------------------
#
#
# Defining a worker named ajp12 and of type ajp12
# Note that the name and the type do not have to match.
#
worker.ajp12.port=8007
worker.ajp12.host=localhost
worker.ajp12.type=ajp12
#
# Specifies the load balance factor when used with
# a load balancing worker.
# Note:
# ----> lbfactor must be > 0
# ----> Low lbfactor means less work done by the worker.
worker.ajp12.lbfactor=1
#
#------ DEFAULT ajp13 WORKER DEFINITION ------------------------------
#---------------------------------------------------------------------
#
# Defining a worker named ajp13 and of type ajp13
# Note that the name and the type do not have to match.
#
worker.ajp13.port=8009
worker.ajp13.host=localhost
worker.ajp13.type=ajp13
#
# Specifies the load balance factor when used with
# a load balancing worker.
# Note:
# ----> lbfactor must be > 0
# ----> Low lbfactor means less work done by the worker.
worker.ajp13.lbfactor=1
#
# Specify the size of the open connection cache.
#worker.ajp13.cachesize
#
#------ DEFAULT LOAD BALANCER WORKER DEFINITION ----------------------
#---------------------------------------------------------------------
#
# The loadbalancer (type lb) workers perform wighted round-robin
# load balancing with sticky sessions.
# Note:
# ----> If a worker dies, the load balancer will check its state
# once in a while. Until then all work is
redirected to peer
# workers.
worker.loadbalancer.type=lb
worker.loadbalancer.balanced_workers=ajp12, ajp13
#
#------ DEFAULT JNI WORKER DEFINITION---------------------------------
#---------------------------------------------------------------------
#
# Defining a worker named inprocess and of type jni
# Note that the name and the type do not have to match.
#
worker.inprocess.type=jni
#
#------ CLASSPATH DEFINITION -----------------------------------------
#---------------------------------------------------------------------
#
# Additional class path components.
#
worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)tomcat.jar
#
# Setting the command line for tomcat.
# Note: The cmd_line string may not contain spaces.
#
worker.inprocess.cmd_line=start
#
# Not needed, but can be customized.
# worker.inprocess.cmd_line=-config
# worker.inprocess.cmd_line=$(workers.tomcat_home)$(ps)conf$(ps)server.xml
# worker.inprocess.cmd_line=-home
# worker.inprocess.cmd_line=$(workers.tomcat_home)
#
# The JVM that we are about to use
#
# This is for Java2
#
# Windows
# worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll
# IBM JDK1.3
#
worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)libjvm.so
# Unix - Sun VM or blackdown
worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)lib$(ps)i386$(ps)classic$(ps)libjvm.so
#
# And this is for jdk1.1.X
#
# worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll
#
# Setting the place for the stdout and stderr of tomcat
#
worker.inprocess.stdout=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stdout
worker.inprocess.stderr=$(workers.tomcat_home)$(ps)logs$(ps)inprocess.stderr
#
# Setting the tomcat.home Java property
#
# worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home)
#
# Java system properties
#
# worker.inprocess.sysprops=java.compiler=NONE
# worker.inprocess.sysprops=myprop=mypropvalue
#
# Additional path components.
#
# worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin
|